10MW级深冷液化空气储能发电系统自动启动控制方法研究

以10 MW级深冷液化空气储能发电系统为研究对象,简要介绍了技术原理、系统构成、主要设备及工艺流程,并从自动控制视角,分别设计了储、释能阶段的启动方法。基于该自动启动方法,可完成储能阶段空气净化及压缩、空气液化、储热和蓄冷子系统的联合运行以及释能阶段储热、蓄冷和膨胀发电子系统的联合运行,实现了储能阶段自动达到额定出液量及释能阶段自动满足额定发电量的需求,提高了能量型机械储能系统对电网负荷变化的响应速度。     

低比转速压气机轮毂轮缘型线多目标优化设计

对电动增压器用低比转速离心压气机轮毂轮缘进行优化设计。采用NUMECA/FINE Design 3D对压气机进行几何参数化,生成数据库样本,利用人工神经网络和遗传算法对轮毂轮缘型线进行优化,并进行流场分析。仿真结果表明,在设计转速为40000 r/min时,优化后设计点压比和效率分别提高6.59%和3.73%。     

直流电对7B04铝合金固溶与时效组织和性能的影响

本文采用拉伸试验、扫描电子显微镜(SEM)和透射电子显微镜(TEM)等手段,研究了7B04铝合金在施加和不施加直流电条件下,经470℃固溶和100-140℃时效处理后的组织和力学性能。与传统的T6处理(470 oC/30 min+120 oC/24h)相比,固溶和/或时效处理时施加500A的电流,可显著提高GPII区的析出密度,进而提高峰时效状态下的拉伸强度和延伸率。固溶过程中施加直流电可将随后时效合金达到峰值强度的时间明显缩短12h。     

Interfacial energy for solutions of nanoparticles,surfactants, and electrolytes

The addition of surfactants to modify the surface property of nanoparticles (NPs) from hydrophilic to hydrophobic also enhances their interfacial properties. Several approaches were previously proposed to calculate the surface tension/interfacial tension (IFT) for different systems in the presence of NPs, surfactants, and electrolytes. However, most of these approaches are indirect and require several measured parameters. Therefore, a mathematical model is developed here to calculate the surface tension/IFT for these systems. The developed model takes into account the cohesive energy due to the interaction of the surfactant CH₂ groups, the electric double layer effect due to the interaction among the ions of NPs, surfactants, and electrolytes, and the dipole–dipole interaction of NPs and electrolytes. The developed model is compared and validated with the laboratory experimental data in literature. The results reveal further understanding of the mechanisms involved in stabilization of oil/water emulsion in the presence of NPs, surfactants, and electrolytes.     

基于CAN总线的多通道开度阀控制系统的设计

针对现有电动阀门控制系统可嵌入性差的问题，设计了一种基于CAN总线的网络化、多通道、开度型阀门嵌入式控制系统。其中，上位机主要用于下达各阀门开度等控制指令并同时监测其工作状态，而下位机采用双MCU架构，主MCU用于控制各阀门的开度大小，从MCU负责采集开度反馈电流以实现闭环控制。下位机采用了模糊PID算法进行控制参数的动态整定，可满足阀门在不同工况下的控制精度要求，并通过OLED屏显示各通道阀门的实际开度值。实验表明,该控制系统运行稳定，能实现对多通道开度阀的精准控制，控制精度在0.6%以内，并支持远程上位机控制和现地控制等多种工作模式。     

Immobilization of surface non-affinitive protein onto a metal surface by an external electric field

1. Download : Download high-res image (279KB)
2. Download : Download full-size image

     

Flash Sintering using Controlled Current Ramp

In conventional flash sintering, the current rises nonlinearly to a set current limit, accompanied by a spike in the power density. This sudden power spike may cause hot spot formation, in which current preferentially channels through a small area, causing localized melting while other areas remain unsintered. By using a controlled current ramp early on the sudden power spike can be avoided. In addition, by changing the ramp rate material properties such as porosity, grain size and conductivity can be tuned.     

Evaluation of the occurrence of mechanical constriction of the Arc in A-TIG welding of austenitic stainless steels

This paper evaluates indications of arc constriction by the thermal and electrical insulation caused by oxides of a single component in A-TIG welding of austenitic stainless steels. Changes in arc dimensions, in its electric voltage and in weld bead morphology caused by three oxide fluxes (SiO₂, Cr₂O₃ e Al₂O₃) applied with two surface densities (30 e 60 g/m2), and with and without a flux-free central strip (of 1, 2 and 4 mm) were studied. Results showed no significant change in the width of the electric arc for the experimental conditions used, therefore not supporting a possible mechanical constriction in the electric arc by oxide electrical and thermal insulation. Lateral filming indicated that the arc is delayed by the fluxes with silica causing the strongest effect. The presence of a clean central strip in the flux layer decreased weld penetration and weld bead cross section, besides the reduction of the width of the bead. Therefore, the results of the present work seem to support Marangoni convection as the main mechanism responsible for increasing penetration in A-TIG welding of stainless austenitic steels.     

红土镍矿冶金技术研究进展

如今世界经济迅猛发展,金属镍的需求量也在加速增长。人们主要从硫化镍矿和红土镍矿中提炼金属镍。然而硫化镍矿资源因大规模开发而不断减少,红土镍矿未来将成为镍的主要来源。因此研究红土镍矿的高效开发利用,是当今围绕镍资源研究的热点,对实际生产具有重要的现实意义。本文简要介绍了镍的应用、开发红土镍矿的意义、红土镍矿的矿物学特性、红土镍矿世界范围内的储量和分布,并且列举并分析了红土镍矿的各种冶炼工艺及其优点与不足,同时综述了有关红土镍矿研究的新方法,为红土镍矿高附加值综合利用研究提出思路。     

Failure of high power varistor ceramic components

Ceramic varistors are electronic components which have a sharp change (over several orders of magnitude) of their electrical resistance at a well-defined voltage (switching voltage). Starting at low voltages, the resistance is large. But by exceeding the switching voltage the resistance drops dramatically and the component acts as a good conductor. Mounted parallel to a consumer, they are used as protection devices against over voltage loading. In the technical routine yearly billions of varistors are used to protect power lines, transformation stations, electronic devices, microelectronic systems or even LEDs.In service large temperature differences may come into existence, which cause severe mechanical stresses that even may destroy the components. The basic principles of the varistor behaviour are explained and examples of mechanical failure are discussed.